395
edits
Changes
→STATUS INDICATIONS: Added Blue LEDs going from middle status
!F
!F
!G
!G
|-
|-
|[[File:TeltoCharge LEDS booting up.gif|center|frameless]]
|[[File:TeltoCharge LEDS booting up.gif|center|frameless]]
|[[File:TeltoCharge LEDS WaitingforEV.gif|center|frameless]]
|[[File:TeltoCharge LEDS WaitingforEV.gif|center|frameless]]
|[[File:TeltoCharge LED WaitingforAuthorization.gif|center|frameless]]
|[[File:TeltoCharge LED WaitingforAuthorization.gif|center|frameless]]
|[[File:TeltoCharge LEDS OnHold.gif|center|frameless|alt=|202x202px]]
|-
|White LED‘s rolling from the bottom to the top – shows that TeltoCharge is booting up
|White pulsing LED‘s – shows that TeltoCharge is in standby mode and waiting for action
|Yellow pulsing LED‘s – shows that TeltoCharge is in standby mode with default settings.
|Yellow LED‘s on – TeltoCharge is not charging, simplified charging sequence is required.
|Blue LED‘s lights up from the middle – TeltoCharge do not require permission, it is waiting for EV to initiate charging process (go to state C).
|Blue LED‘s pulsing – permission to charge is not granted. TeltoCharge requires authorization.
|Blue LED‘s rolldown from up to down
1. Wait for scheduled time.
2. No dynamic power – DLB/DLM/Solar enabled and no sufficient power.
3. EVSE suspended.
4. Reserved charge.
|-
|
|
|Open installer menu via Teltonika Energy app, set and save settings.
|Open installer menu via Teltonika Energy app and select to allow simplified charging sequence
|
|Authorize yourself with app or NFC card.
|1. Go to settings via Teltonika energy APP and select schedule time section to check for set graphs
2. Wait for more available power or increase amperage limits via settings (if your grid allows it)
3. Available power is less than 6 Amperes. Provide more power or wait for more to generate.
4. Other user has already reserved this charging station (OCPP only)
|}
{| class="wikitable"
|+
!H
! I
!J
! K
!L
!M
!N
|-
|[[File:TeltoCharge LEDS AddNFC.gif|center|frameless]]
|[[File:TeltoCharge LEDS AddNFC.gif|center|frameless]]
|[[File:TeltoCharge LEDS InitialisationOfCharging.gif|center|frameless]]
|[[File:TeltoCharge LEDS InitialisationOfCharging.gif|center|frameless]]
|[[File:TeltoCharge LEDS AuthorizationAccepted.PNG|center|frameless|alt=|204x204px]]
|[[File:TeltoCharge LEDS AuthorizationAccepted.PNG|center|frameless|alt=|204x204px]]
|-
|-
| Four middle blue LED’s pulsing – TeltoCharge waiting to add new NFC card
|Four middle blue LED’s pulsing – TeltoCharge waiting to add new NFC card
|Green LED‘s pulsing - Initialisation of charging.
|Green LED‘s pulsing - Initialisation of charging.
|Green LED‘s rolling upwards from the bottom – TeltoCharge is in charging process.
|Green LED‘s rolling upwards from the bottom – TeltoCharge is in charging process.
| Green LED‘s on – TeltoCharge finished charging.
|Green LED‘s on – TeltoCharge finished charging.
|Purple LED‘s on – TeltoCharge requires ventilation (charging is done in state D).
|Purple LED‘s on – TeltoCharge requires ventilation (charging is done in state D).
|Red four middle LED's - NFC/RFID card declined from the server.
|Red four middle LED's - NFC/RFID card declined from the server.
|Green four middle LED's - NFC/RFID card accepted from the server.
|Green four middle LED's - NFC/RFID card accepted from the server.
|-
|-
|
|
|
|
|-
|-
|Input voltage error.
|Input voltage error.
|Output voltage/current error.
| Output voltage/current error.
|Current leakage detected.
|Current leakage detected.
|Connectivity error.
| Connectivity error.
|Temperature error.
|Temperature error.
|Internal errors.
|Internal errors.
|Faulty connection to EV.
|Faulty connection to EV.
|Warning orange LED
|Warning orange LED
|-
|-
|Overvoltage;
|Overvoltage;
Output current.
Output current.
|Current leakage detected
|Current leakage detected
|Cable lock;
| Cable lock;
PP fail;
PP fail;
Car diode.
Car diode.
|Temperature reached 85°C
|Temperature reached 85°C
| -12V;
| -12V;
|CP fail
|CP fail
|
|
Problems with energy meter:
Problems with energy meter:
* Unrecognized;
*Unrecognized;
* Badly set;
*Badly set;
* Communication problems;
*Communication problems;
Other problems:
Other problems:
* Temperature;
*Temperature;
* Current ;
*Current ;
* D state.
*D state.
|-
|-
| colspan="8" |<center><big>Troubleshooting</big></center>
| colspan="8" |<center><big>Troubleshooting</big></center>
|-
|-
|
|
*Check if input wiring is connected correctly;
*Check if input wiring is connected correctly;
*Measure input voltage;
* Measure input voltage;
*Check installer menu settings if supply voltage and voltage tolerance is in accordance with the measured input voltage.
*Check installer menu settings if supply voltage and voltage tolerance is in accordance with the measured input voltage.
|
|
*Disconnect charging cable from the EV and check if the issue remains.
* Disconnect charging cable from the EV and check if the issue remains.
*Reboot charger and try to connect EV again.
* Reboot charger and try to connect EV again.
|
|
*Disconnect the cable from the EV and check if the error persists.
*Disconnect the cable from the EV and check if the error persists.
*Check if the inside of both the socket and the plug has no foreign materials inside (is clean).
*Check if the inside of both the socket and the plug has no foreign materials inside (is clean).
*Check visually if the cable is not damaged.
*Check visually if the cable is not damaged.
*Check if the boards are not covered in dust and/or other materials.
* Check if the boards are not covered in dust and/or other materials.
|
|
* Check if the charging cable is connected correctly from the charger side (socket version) and from the EV side;
*Check if the charging cable is connected correctly from the charger side (socket version) and from the EV side;
*Try to reconnect charging cable to the EV and EVSE (if it is socket version).
*Try to reconnect charging cable to the EV and EVSE (if it is socket version).
*Listen if you can hear a clicking sound from the TeltoCharge when you plug the cable to EV. Charger should lock cable plug. If you can’t hear, try to unplug cable (from EVSE side) while it is plugged from EV side. If it is possible to unplug, report this problem via VIP helpdesk or your sales manager.
*Listen if you can hear a clicking sound from the TeltoCharge when you plug the cable to EV. Charger should lock cable plug. If you can’t hear, try to unplug cable (from EVSE side) while it is plugged from EV side. If it is possible to unplug, report this problem via VIP helpdesk or your sales manager.
|
|
*Try reconnect charging cable from the EV side. There might be control pilot communication problem which can occur with different EV models.
*Try reconnect charging cable from the EV side. There might be control pilot communication problem which can occur with different EV models.
|Go to the live data section and see what is the main problem.
| Go to the live data section and see what is the main problem.
* Check connected wires via TeltoCharge and energy meter inputs;
*Check connected wires via TeltoCharge and energy meter inputs;
* Check if the energy meter is compatible;
*Check if the energy meter is compatible;
* Check temperature.
*Check temperature.
|-
|-
| colspan="13" |<center><big>'''What to do to avoid'''</big></center>
| colspan="13" |<center><big>'''What to do to avoid'''</big></center>
|-
|-
|
|
Connected EV uses Simplified charging sequence. Charging power is limited. In installer menu option „Simplified charging sequence“ must be turned ON.
Connected EV uses Simplified charging sequence. Charging power is limited. In installer menu option „Simplified charging sequence“ must be turned ON.
|
|
|
|
