ABB settings: Difference between revisions

Revision as of 11:33, 8 May 2023

RS485 parameters for energy meters ABB A41 ; A42 ; A43 ; A44 ; B21 ; B23 ; B24

Note: Energy meter parameters should match EVSE default parameters.

RS485 parameter	EVSE default parameter value (configurable in mobile app)
Modbus adress	1
Baud rate	9600
Parity	Even
Stop bits	1

How to configure Smart energy meter in mobile application

Note 1: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).
Note 2: While connecting ABB B23 energy meter, it is recommended to switch places of A and B wires ( A goes to B and B goes to A)

1. Make sure you have updated mobile application and firmware version of the charger to the latest. (←Firmware and iOS / Android).

2. Go to installer menu in your application and set general parameters from table above:

3. To get data form energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section:

4. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it:

To find out specific settings, you will need to read the energy meter's documentation.

← Smart energy meters

@@ Line 22: / Line 22: @@
 |}
-==== Configuring the meter in the mobile application ====
+==== How to configure Smart energy meter in mobile application ====
+''Note 1: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''<br>
+''Note 2: While connecting ABB B23 energy meter, it is recommended to switch places of A and B wires ( A goes to B and B goes to A)''
+. Make sure you have updated mobile application and firmware version of the charger to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).
+. Go to installer menu in your application and set general parameters from table above:
+[[file:General_meter_settings.png|alt=|left|frameless|]]
-''Note: Users can use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''
-<br>
-''Note 2: While connecting ABB B23 energy meter, it is recommended to switch places of A and B wires ( A goes to B and B goes to A)''
-. Make sure your charger firmware and application are updated to the latest version. (←[[Release notes: Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).
-. Enter the Installer menu, select Load Balancing, then Modbus RTU.
+. To get data form energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section:
+[[file:Dynamic_load_balancing.png|alt=|left|frameless|]]
-[[File:Settings-to-rtu.png|frameless|576x576px]]
-. If the charger does not recognize the meter, go to Manual Setup to use a device preset (choose the model of ''your meter'') or enter the settings from the RS485 parameters table manually.
+. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it:
-[[File:Mod-to-manual.png|frameless|576x576px]]
+[[file:Meter_for_power_consumption_calculation.png|alt=|left|frameless|]]
-Once the meter is successfully configured, press Connect. You will receive a confirmation screen and its status will change to "'''Connected'''". <br>If you get the status: <br>'''Disconnected''' - wrong EVSE parameter value is set or meter is not wired correctly. <br>'''Wrong type'''  - the meter configuration does not match one that is currently connected. <br>'''Not supported''' - the connected meter is not compatible with the installation.
@@ Line 59: / Line 72: @@
-For detailed settings, refer to the energy meter's official documentation.
+To find out specific settings, you will need to read the energy meter's documentation.
 ← [[Smart energy meters]]