Line 1: |
Line 1: |
| + | ← [[Smart energy meters]] |
| ==== RS485 parameters for energy meter Siemens PAC1020 ; PAC2200 ; PAC3100 ; PAC3120 ; Siemens PAC3200 ; Siemens PAC3220 ; Siemens PAC4200 ==== | | ==== RS485 parameters for energy meter Siemens PAC1020 ; PAC2200 ; PAC3100 ; PAC3120 ; Siemens PAC3200 ; Siemens PAC3220 ; Siemens PAC4200 ==== |
| ''Note: Energy meter parameters should match EVSE default parameters.'' | | ''Note: Energy meter parameters should match EVSE default parameters.'' |
Line 11: |
Line 12: |
| |- | | |- |
| | style="padding: 8px;" | Baud rate | | | style="padding: 8px;" | Baud rate |
− | | style="padding: 8px;" | 9600 | + | | style="padding: 8px;" | 19200 |
| |- | | |- |
| | style="padding: 8px;" | Parity | | | style="padding: 8px;" | Parity |
Line 18: |
Line 19: |
| |- | | |- |
| | style="padding: 8px;" | Stop bits | | | style="padding: 8px;" | Stop bits |
− | | style="padding: 8px;" | 1 | + | | style="padding: 8px;" | 2 |
| | | |
| |} | | |} |
| + | |
| + | ==== How to configure Smart energy meter in mobile application ==== |
| + | |
| + | ''Note: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).'' |
| + | |
| + | |
| + | 1. Make sure you have updated mobile application and firmware version of the charger to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]). |
| + | |
| + | 2. Go to installer menu in your application and set general parameters from table above: |
| + | |
| + | [[file:General_meter_settings.png|alt=|left|frameless|]] |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | 3. To get data form energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section: |
| + | |
| + | [[file:Dynamic_load_balancing.png|alt=|left|frameless|]] |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | 4. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it: |
| + | |
| + | [[file:Meter_for_power_consumption_calculation.png|alt=|left|frameless|]] |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | |
| + | To find out specific settings, you will need to read the energy meter's documentation. |
| + | |
| + | |
| + | |
| + | ← [[Smart energy meters]] |