Installation process (NA)

General specifications

Teltocharge tethered with Type 1 cable

Dimensions without cable	170x341x97 mm
Weight without cable	2.8 kg
Operating temperature	-30°C - +50°C
IP rating	IP55
IK rating	IK10
Certification	UL2594
In compliance with	IEC 61851-1

Electrical specifications

Here you can find information about electric parameters of Teltocharge product

AC INPUT SPECIFICATIONS
Maximum power	7,6 kW	9,6 kW	11,5 kW
Input AC power connection	2 phases
Maximum current	32 A	40 A	48 A
Input voltage	2 phases: (L-L) 240 ± 10% VAC
Rated frequency	50 / 60 HZ
Standby power consumption	4 W
Earth (ground) fault protection	20 mA AC, 6 mA DC
Overvoltage category	OVC II
Protection against electric shock	Class I
AC Output specifications
AC output voltage range	1 phase: (L-N) 240 ± 10% VAC
Connection Standart	Type 1 cable
Connection to the grid	NEMA 6-50 plug to the wall socket		Direct cable from house grid (Hardwired)
Power Cable
Maximum cable diameter	17.5 mm		20,75 mm
Maximum wire cross section	7.5 mm2

Product code structure

On the product Middle plate you can find markings showing its Product name and code, Certifications, Serial number and more.

Model	Version	Power	Connector	Connectivity	Front plate color	Front plate finish
A	B	C	D	E	F	G
EVC	1 - V1	3 - US 7,6 kW, 1/2P, 32A, 120/240V 4 - US 9,6 kW, 1/2P, 40A, 120/240V 5 - US 11.5kW, 1/2P, 48A, 120/240V	1 - Tethered cable	0 - Without GSM modem	P - Gray R - Red M - Blue B - White 0 - N/A	0 –  Without front panel 1 – Tethered cable

Required tools

List of required tools include:

A - Hammer
B - Electric drill
C - Pencil
D - Screwdriver
E - Cutting pliers
F - Allen key 2,5 mm
G - Measuring tape
H - Utility knife
I - Level
J - Drill bit D6

Included Mounting parts

Included in the box you will find:

K - Wall plugs 6x35 mm
L - Pan head self-tapping screws galvanized steel
M - DIN912 M3x8 screws
N - Cable gland
O - Rubber washer

EV Charger Main elements

Site preparation requirements

• Find a suitable site on a wall (The mounting surface required to be flat and stable, for example a finished, brick or concrete wall. Wall required to be suitable to withstand TeltoCharge weight with charging cable)​.
• Make sure that the required power supply is easily accessible. (Required power supply depends on the type of charger).
• Recommendation is not to install TeltoCharge on direct sunlight to avoid overheating.

Installation process

Housing Installation

A - Place the drilling template on the wall and mark the three fixing points.

B - Drill holes where the fixing points are marked.

C - Insert the wall plugs into the fixing holes.

Fix the device on the wall by inserting the self-tapping screws with rubber washers (start with the top screw and make sure the housing is horizontal)

Electrical wiring

Network type:
A - IT/TT two phase set up.

Notice 1: Products EVC131 (32Amp) and EVC141 (40 Amp) come with pre-wired NEMA 6-50 plug. These models have to be connected to pro properly selected wall socket which meets the same NEMA 6-50 standard.
Notice 2: Voltages in different installations may vary. Please check configuration of Installer menu Connection type settings in mobile application and select either delta or star connection.

Closing the middle panel

A - Place a middle panel on the housing and press it, till it clicks.

B - Fix it using DIN912 M3x8 screws;

Closing the front plate;

C - Lock the top of the plate;

D - Lock the bottom of the plate;

E - Fix it using DIN912 M3x8 screws;

LED indicators

Information about how LED indicators signal different states can be obtained from here