22 kW TeltoCharge Suggested configuration: Difference between revisions

Latest revision as of 10:26, 18 July 2023

Introduction

Suggested configuration of 22 kW power TeltoCharge installer menu

electrical grid

1 phase (1L+N+PE) | voltage between L-N 230V ± 10%

Suggested installer menu configuration guide

Option number in installer	Installer menu parameter name	Suggested value to set	Link to description of parameter
01	Max power from grid	32 A	Max power from grid
02	Supply voltage	230 V	Supply voltage
03	Upper voltage tolerance	10 %	Upper voltage tolerance
04	Lower voltage tolerance	10 %	Lower voltage tolerance
05	Three phase charging	OFF	Three phase charging
06	Phase priority	L1	Phase priority
07	Difference between phases	120 °	Difference between phases
08	Use neutral as phase	OFF	Use neutral as phase
09	Use data from energy meter	OFF	Use data from energy meter
10	kWh meter address	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - follow link on the right.	Choose your Smart energy meter and its parameters
11	Energy meter type	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
12	RS-485 baudrate	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
13	RS-485 parity	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
14	RS-485 stop bit	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
15	Dynamic load balancing	OFF	Dynamic Load Balancing
16	Use preferred phase	Not needed to adjust if Dynamic load balancing is OFF.	Use prefered phase
17	Energy meter address	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.	Choose your Smart energy meter and its parameters
18	Allow simplified charging sequence	OFF	Allow simplified charging sequence
19	Charger location is ventilated	OFF (if your TeltoCharge is inside the property)	Charger location is ventilated
20	Temperature warning	60 °C	Temperature warning

3 phase (3L+N+PE) | voltage between L-N 230V ± 10% | L-L 400V ± 10%

Suggested installer menu configuration guide

maximum

Option number in installer	Installer menu parameter name	Suggested value to set	Link to description of parameter
01	Max power from grid	32 A	Max power from grid
02	Supply voltage	230 V	Supply voltage
03	Upper voltage tolerance	10 %	Upper voltage tolerance
04	Lower voltage tolerance	10 %	Lower voltage tolerance
05	Three phase charging	ON	Three phase charging
06	Phase priority	L1	Phase priority
07	Difference between phases	120 °	Difference between phases
08	Use neutral as phase	OFF	Use neutral as phase
09	Use data from energy meter	OFF	Use data from energy meter
10	kWh meter address	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - follow link on the right.	Choose your Smart energy meter and its parameters
11	Energy meter type	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
12	RS-485 baudrate	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
13	RS-485 parity	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
14	RS-485 stop bit	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.
15	Dynamic load balancing	OFF	Dynamic Load Balancing
16	Use preferred phase	Not needed to adjust if Dynamic load balancing is OFF.	Use prefered phase
17	Energy meter address	Not needed to adjust if Dynamic load balancing is OFF. If it's ON - you must follow link on the right.	Choose your Smart energy meter and its parameters
18	Allow simplified charging sequence	OFF	Allow simplified charging sequence
19	Charger location is ventilated	OFF (if your TeltoCharge is inside the property)	Charger location is ventilated
20	Temperature warning	60 °C	Temperature warning

@@ Line 6: / Line 6: @@
    <ul style="list-style-type: none; margin: 0; padding: 0;">
 <br>
-To run your 11 kW TeltoCharge on 1 phase, please follow this link to suggested parameters: [[7.4 kW TeltoCharge Suggested configuration]]. With 1-phase of 11 kW TeltoCharge you can achieve to charge at maximum 7.4 kW power.
+To run your 22 kW TeltoCharge on 1 phase, please follow this table below with suggested configurations.
+ <h2 style="color: #4a4a4a; font-size: 24px; font-weight: bold; margin-bottom: 10px;">Suggested installer menu configuration guide</h2>
+  <ul style="list-style-type: none; margin: 0; padding: 0;">
+With 1-phase of 22 kW TeltoCharge you can achieve to charge at maximum 7.4 kW power.
+{| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"
+|-
+! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" | Option number in installer
+! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" | Installer menu parameter name
+! style="background-color: #0054A6; color:#FFFFFF; padding: 4px;" | Suggested value to set
+! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" | Link to description of parameter
+|-
+| style="padding: 8px;" | 01
+| style="padding: 8px;" | '''Max power from grid'''
+| style="padding: 8px;" | 32 A
+| style="padding: 8px;" | [[Max power from grid]]
+|-
+| style="padding: 8px;" | 02
+| style="padding: 8px;" | '''Supply voltage '''
+| style="padding: 20px;" | 230 V
+| style="padding: 8px;" | [[Supply voltage]]
+|-
+| style="padding: 8px;" | 03
+| style="padding: 8px;" | '''Upper voltage tolerance'''
+| style="padding: 8px;" | 10 %
+| style="padding: 8px;" | [[Upper voltage tolerance]]
+|-
+| style="padding: 8px;" | 04
+| style="padding: 8px;" | '''Lower voltage tolerance'''
+| style="padding: 8px;" | 10 %
+| style="padding: 8px;" | [[Lower voltage tolerance]]
+|-
+| style="padding: 8px;" | 05
+| style="padding: 8px;" | '''Three phase charging'''
+| style="padding: 8px;" | OFF
+| style="padding: 8px;" | [[Three phase charging]]
+|-
+| style="padding: 8px;" | 06
+| style="padding: 8px;" | '''Phase priority'''
+| style="padding: 8px;" | L1
+| style="padding: 8px;" | [[Phase priority]]
+|-
+| style="padding: 8px;" | 07
+| style="padding: 8px;" | '''Difference between phases'''
+| style="padding: 8px;" | 120 °
+| style="padding: 8px;" | [[Difference between phases]]
+|-
+| style="padding: 8px;" | 08
+| style="padding: 8px;" | '''Use neutral as phase'''
+| style="padding: 8px;" | OFF
+| style="padding: 8px;" | [[Use neutral as phase]]
+|-
+| style="padding: 8px;" | 09
+| style="padding: 8px;" | '''Use data from energy meter'''
+| style="padding: 8px;" | OFF
+| style="padding: 8px;" | [[Use data from energy meter]]
+|-
+| style="padding: 8px;" | 10
+| style="padding: 8px;" | '''kWh meter address'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - follow link on the right.''
+| style="padding: 8px;" rowspan="5" | [https://wiki.teltonika-energy.com/view/Smart_energy_meters#TeltoCharge_supported_smart_energy_meters Choose your Smart energy meter and its parameters]
+|-
+| style="padding: 8px;" | 11
+| style="padding: 8px;" | '''Energy meter type'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
+|-
+| style="padding: 8px;" | 12
+| style="padding: 8px;" | '''RS-485 baudrate'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
+|-
+| style="padding: 8px;" | 13
+| style="padding: 8px;" | '''RS-485 parity'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
+|-
+| style="padding: 8px;" | 14
+| style="padding: 8px;" | '''RS-485 stop bit'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
+|-
+| style="padding: 8px;" | 15
+| style="padding: 8px;" | '''Dynamic load balancing'''
+| style="padding: 8px;" | OFF
+| style="padding: 8px;" | [[Dynamic Load Balancing]]
+|-
+| style="padding: 8px;" | 16
+| style="padding: 8px;" | '''Use preferred phase'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.'''
+| style="padding: 8px;" | [[Use prefered phase]]
+|-
+| style="padding: 8px;" | 17
+| style="padding: 8px;" | '''Energy meter address'''
+| style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
+| style="padding: 8px;" | [https://wiki.teltonika-energy.com/view/Smart_energy_meters#TeltoCharge_supported_smart_energy_meters Choose your Smart energy meter and its parameters]
+|-
+| style="padding: 8px;" | 18
+| style="padding: 8px;" | '''Allow simplified charging sequence'''
+| style="padding: 8px;" | OFF
+| style="padding: 8px;" | [[Allow simplified charging sequence]]
+|-
+| style="padding: 8px;" | 19
+| style="padding: 8px;" | '''Charger location is ventilated'''
+| style="padding: 8px;" | OFF (if your TeltoCharge is inside the property)
+| style="padding: 8px;" | [[Charger location is ventilated]]
+|-
+| style="padding: 8px;" | 20
+| style="padding: 8px;" | '''Temperature warning'''
+| style="padding: 8px;" | 60 °C
+| style="padding: 8px;" | [[Temperature warning]]
+|}
    <h2 style="color: #4a4a4a; font-size: 24px; font-weight: bold; margin-bottom: 10px;">3 phase (3L+N+PE) | voltage between L-N 230V ± 10% | L-L 400V ± 10%</h2>
    <ul style="list-style-type: none; margin: 0; padding: 0;">
@@ Line 42: / Line 150: @@
 | style="padding: 8px;" | 10 %
 | style="padding: 8px;" | [[Lower voltage tolerance]]
 |-
 | style="padding: 8px;" | 05
+| style="padding: 8px;" | '''Three phase charging'''
+| style="padding: 8px;" | ON
+| style="padding: 8px;" | [[Three phase charging]]
+|-
+| style="padding: 8px;" | 06
 | style="padding: 8px;" | '''Phase priority'''
 | style="padding: 8px;" | L1
 | style="padding: 8px;" | [[Phase priority]]
 |-
-| style="padding: 8px;" | 06
+| style="padding: 8px;" | 07
 | style="padding: 8px;" | '''Difference between phases'''
-| style="padding: 8px;" | 180 °
+| style="padding: 8px;" | 120 °
 | style="padding: 8px;" | [[Difference between phases]]
 |-
-| style="padding: 8px;" | 07
+| style="padding: 8px;" | 08
 | style="padding: 8px;" | '''Use neutral as phase'''
 | style="padding: 8px;" | OFF
 | style="padding: 8px;" | [[Use neutral as phase]]
 |-
-| style="padding: 8px;" | 08
+| style="padding: 8px;" | 09
 | style="padding: 8px;" | '''Use data from energy meter'''
 | style="padding: 8px;" | OFF
 | style="padding: 8px;" | [[Use data from energy meter]]
 |-
-| style="padding: 8px;" | 09
+| style="padding: 8px;" | 10
 | style="padding: 8px;" | '''kWh meter address'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - follow link on the right.''
 | style="padding: 8px;" rowspan="5" | [https://wiki.teltonika-energy.com/view/Smart_energy_meters#TeltoCharge_supported_smart_energy_meters Choose your Smart energy meter and its parameters]
 |-
-| style="padding: 8px;" | 10
+| style="padding: 8px;" | 11
 | style="padding: 8px;" | '''Energy meter type'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
 |-
-|-
+| style="padding: 8px;" | 12
-| style="padding: 8px;" | 11
 | style="padding: 8px;" | '''RS-485 baudrate'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
 |-
-| style="padding: 8px;" | 12
+| style="padding: 8px;" | 13
 | style="padding: 8px;" | '''RS-485 parity'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
 |-
-| style="padding: 8px;" | 13
+| style="padding: 8px;" | 14
 | style="padding: 8px;" | '''RS-485 stop bit'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
 |-
-| style="padding: 8px;" | 14
+| style="padding: 8px;" | 15
 | style="padding: 8px;" | '''Dynamic load balancing'''
 | style="padding: 8px;" | OFF
 | style="padding: 8px;" | [[Dynamic Load Balancing]]
 |-
-| style="padding: 8px;" | 15
+| style="padding: 8px;" | 16
 | style="padding: 8px;" | '''Use preferred phase'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.'''
 | style="padding: 8px;" | [[Use prefered phase]]
 |-
-| style="padding: 8px;" | 16
+| style="padding: 8px;" | 17
 | style="padding: 8px;" | '''Energy meter address'''
 | style="padding: 8px;" | '''Not needed to adjust if Dynamic load balancing is OFF.''' <br> ''If it's ON - you must follow link on the right.''
 | style="padding: 8px;" | [https://wiki.teltonika-energy.com/view/Smart_energy_meters#TeltoCharge_supported_smart_energy_meters Choose your Smart energy meter and its parameters]
 |-
-| style="padding: 8px;" | 17
+| style="padding: 8px;" | 18
 | style="padding: 8px;" | '''Allow simplified charging sequence'''
 | style="padding: 8px;" | OFF
 | style="padding: 8px;" | [[Allow simplified charging sequence]]
 |-
-| style="padding: 8px;" | 18
+| style="padding: 8px;" | 19
 | style="padding: 8px;" | '''Charger location is ventilated'''
 | style="padding: 8px;" | OFF (if your TeltoCharge is inside the property)
 | style="padding: 8px;" | [[Charger location is ventilated]]
 |-
-| style="padding: 8px;" | 19
+| style="padding: 8px;" | 20
 | style="padding: 8px;" | '''Temperature warning'''
 | style="padding: 8px;" | 60 °C
 | style="padding: 8px;" | [[Temperature warning]]
 |}