Line 1: |
Line 1: |
− | ==Site preparation requirements==
| |
− | * Find a suitable site on a wall (The mounting surface required to be flat and stable, for example a finished, brick or concrete wall. Wall required to be suitable to withstand TeltoCharge weight with charging cable).
| |
− | * Make sure that the required power supply is easily accessible. (Required power supply depends on the type of charger).
| |
− | * Make sure that TeltoCharge is not installed on direct sunlight.
| |
| ==Installation process== | | ==Installation process== |
− | ===Drilling=== | + | ===Housing Installation=== |
| [[File:TeltoCharge Installation InstallationProcess DrillingA.png|border|frameless]]'''A''' - Place the drilling template on the wall and mark the three fixing points. | | [[File:TeltoCharge Installation InstallationProcess DrillingA.png|border|frameless]]'''A''' - Place the drilling template on the wall and mark the three fixing points. |
| | | |
Line 11: |
Line 7: |
| [[File:TeltoCharge Installation InstallationProcess DrillingC.png|border|frameless]]'''C''' - Insert the wall plugs into the fixing holes. | | [[File:TeltoCharge Installation InstallationProcess DrillingC.png|border|frameless]]'''C''' - Insert the wall plugs into the fixing holes. |
| | | |
− | === Housing Installation ===
| + | [[File:TeltoCharge Installation InstallationProcess HousingInstallation.png|border|frameless|214x214px]] |
− | [[File:TeltoCharge Installation InstallationProcess HousingInstallation.png|border|frameless]] | |
| | | |
| 1. Fix the device on the wall by inserting the self-tapping screws (start with the top screw and make sure the housing is horizontal). | | 1. Fix the device on the wall by inserting the self-tapping screws (start with the top screw and make sure the housing is horizontal). |
| | | |
− | 2. Make sure the cable grommet is properly mounted on the cables (AC input cable and Ethernet cable). | + | 2. Make sure the cable gland is properly mounted on the cables (AC input cable and Ethernet cable). |
− | ===Electrical wiring===
| |
− | [[File:TeltoCharge Installation InstallationProcess ElectricalWiring.PNG|border|frameless|518x518px]]
| |
| | | |
− | '''A''' - T/N single phase set up;
| |
| | | |
− | '''B''' - T/N Three phase set up;
| + | [[Category: Getting Started]] |
− | | |
− | '''C''' - IT/TT three phase set up;
| |
− | | |
− | '''D''' - IT/TT single phase set up;
| |
− | | |
− | === SIM card installation ===
| |
− | [[File:TeltoCharge Installation InstallationProcess SIMCardInstallation.PNG|border|frameless]]
| |
− | | |
− | Insert a nano SIM card into card slot.
| |
− | | |
− | === Closing the middle panel ===
| |
− | [[File:TeltoCharge Installation InstallationProcess ClosingMiddlePanel.PNG|border|frameless|512x512px]]
| |
− | | |
− | '''A''' - Place a middle panel on the housing;
| |
− | | |
− | '''B''' - Fix it using DIN912 M3x8 screws;
| |
− | | |
− | === Closing the front plate; ===
| |
− | [[File:TeltoCharge Installation InstallationProcess ClosingFrontPanel.PNG|border|frameless|473x473px]]
| |
− | | |
− | '''A''' - Insert the upper part of the front plate to the fixing holes and fix the plate;
| |
− | | |
− | '''B''' - Fix it using DIN912 M3x8 screws;
| |
− | | |
− | '''C''' - Lock the top of the plate;
| |
− | | |
− | '''D''' - Lock the bottom of the plate;
| |
− | | |
− | '''E''' - Fix it using DIN912 M3x8 screws;
| |
− | | |
− | [[Category: Installation]] | |