UseCases2 - Revision history

KarolisS: /* 2.Installation with the smart meter using (Dynamic Load Balancing) */

2025-08-05T10:20:17Z

2.Installation with the smart meter using (Dynamic Load Balancing)

← Older revision		Revision as of 13:20, 5 August 2025
Line 20:		Line 20:
	=2.Installation with the smart meter using (Dynamic Load Balancing) =		=2.Installation with the smart meter using (Dynamic Load Balancing) =
	Installation type, when TeltoCharge is connected with the Smart meter (list to supported smart meters) .		Installation type, when TeltoCharge is connected with the Smart meter (list to supported smart meters) .
	TeltoCharge ~~have~~ the ability to communicate with dedicated smart energy meter and regarding to its readings, adjust used electrical power. Such functionality allows to ~~protection~~ house electrical grid from overload in peak hours and optimize energy usage to meet user habits. A smart energy meter should always be installed in source electrical cabinet as showed below.		TeltoCharge has the ability to communicate with dedicated smart energy meter and regarding to its readings, adjust used electrical power. Such functionality allows to protect house electrical grid from overload in peak hours and optimize energy usage to meet user habits. A smart energy meter should always be installed in source electrical cabinet as showed below.
	{\| class="wikitable"		{\| class="wikitable"
	\|+ Caption text		\|+ Caption text

DonatasL at 11:38, 5 March 2025

2025-03-05T11:38:50Z

← Older revision		Revision as of 14:38, 5 March 2025
Line 144:		Line 144:
	''		''
	''*If there are more specific requirements needed please visit "advanced functionalities link"''''		''*If there are more specific requirements needed please visit "advanced functionalities link"''''
	~~=4.Connecting to 3rd party OCPP provider=~~
	~~Installation type, where all the control are given to the 3rd party OCPP provider. (List of the OCPP providers).~~
	~~{\| class="wikitable"~~
	~~\|+ Caption text~~
	\|-
	~~! Header text !! Header text !! Header text~~
	\|-
	~~\| Power selector switch \|\| Must be selected according to the installation details \|\| Example~~
	\|-
	~~\| Connectivity \|\| Connect TeltoCharge to the internet \|\| Example~~
	\|-
	~~\| OCPP \|\| ON \|\| Example~~
	\|-
	~~\| URL \|\| Write provided url.~~
	~~URL must end with “/~~
	~~\|Most of the time it's provided from OCPP provider~~
	\|-
	~~\| Charge point id \|\| Write provided ID \|\| Most of the time S/N of the device~~
	\|}

DonatasL at 11:25, 5 March 2025

2025-03-05T11:25:53Z

← Older revision		Revision as of 14:25, 5 March 2025
Line 135:		Line 135:
	\|-\|-		\|-\|-
	\|Secondary device ID		\|Secondary device ID
	\|1 (+1 for each new follower)		\|2 (+1 for each new follower)
	\|Link to advanced settings		\|Link to advanced settings
	\|-		\|-

DonatasL at 11:08, 5 March 2025

2025-03-05T11:08:10Z

← Older revision		Revision as of 14:08, 5 March 2025
Line 18:		Line 18:
	\| Phase priority \|\| Select phase from which you would to charge when operating on single phase mode \|\| Link to QUG		\| Phase priority \|\| Select phase from which you would to charge when operating on single phase mode \|\| Link to QUG
	\|}		\|}
	=2.Installation with the smart meter using ~~DLB~~ =		=2.Installation with the smart meter using (Dynamic Load Balancing) =
	Installation type, when TeltoCharge is connected with the Smart meter (list to supported smart meters) .		Installation type, when TeltoCharge is connected with the Smart meter (list to supported smart meters) .
	TeltoCharge have the ability to communicate with dedicated smart energy meter and regarding to its readings, adjust used electrical power. Such functionality allows to protection house electrical grid from overload in peak hours and optimize energy usage to meet user habits. A smart energy meter should always be installed in source electrical cabinet as showed below.		TeltoCharge have the ability to communicate with dedicated smart energy meter and regarding to its readings, adjust used electrical power. Such functionality allows to protection house electrical grid from overload in peak hours and optimize energy usage to meet user habits. A smart energy meter should always be installed in source electrical cabinet as showed below.

DonatasL: Protected "UseCases2" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2025-02-21T13:02:22Z

Protected "UseCases2" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 16:02, 21 February 2025
(No difference)

DonatasL at 11:59, 18 February 2025

2025-02-18T11:59:03Z

← Older revision		Revision as of 14:59, 18 February 2025
Line 144:		Line 144:
	''		''
	''*If there are more specific requirements needed please visit "advanced functionalities link"''''		''*If there are more specific requirements needed please visit "advanced functionalities link"''''
			=4.Connecting to 3rd party OCPP provider=
			Installation type, where all the control are given to the 3rd party OCPP provider. (List of the OCPP providers).
			{\| class="wikitable"
			\|+ Caption text
			\|-
			! Header text !! Header text !! Header text
			\|-
			\| Power selector switch \|\| Must be selected according to the installation details \|\| Example
			\|-
			\| Connectivity \|\| Connect TeltoCharge to the internet \|\| Example
			\|-
			\| OCPP \|\| ON \|\| Example
			\|-
			\| URL \|\| Write provided url.
			URL must end with “/
			\|Most of the time it's provided from OCPP provider
			\|-
			\| Charge point id \|\| Write provided ID \|\| Most of the time S/N of the device
			\|}

DonatasL at 11:54, 18 February 2025

2025-02-18T11:54:50Z

@@ Line 17: / Line 17: @@
 |-
 | Phase priority  || Select phase from which you would to charge when operating on single phase mode   || Link to QUG
 |}
 =2.Installation with the smart meter using DLB =
@@ Line 96: / Line 95: @@
 Modbus TCP (WiFi or ethernet cable)
 | Example
 |}

DonatasL at 11:33, 18 February 2025

2025-02-18T11:33:53Z

@@ Line 55: / Line 55: @@
 |-
 | Other Funtionalities || Here you could read more about all other functionalities || Example
 |}

DonatasL: Created page with "=USE CASES= Depending on the installation, the most common installation types are listed here. In the configuration table mentioned only the parameters that must be changed =1.Installation without the Smart meter= Installation type, when TeltoCharge is connected without any other device from where the data could be used. In that kind of installations, it’s important to limit TeltoCharge to prevent breaking Circuit Breaker. {| class="wikitable" |+ Example settings..."

2025-02-18T11:29:31Z

Created page with "=USE CASES= Depending on the installation, the most common installation types are listed here. In the configuration table mentioned only the parameters that must be changed =1.Installation without the Smart meter= Installation type, when TeltoCharge is connected without any other device from where the data could be used. In that kind of installations, it’s important to limit TeltoCharge to prevent breaking Circuit Breaker. {| class="wikitable" |+ Example settings..."

New page

=USE CASES=
Depending on the installation, the most common installation types are listed here. In the configuration table mentioned only the parameters that must be changed
=1.Installation without the Smart meter=
Installation type, when TeltoCharge is connected without any other device from where the data could be used. In that kind of installations, it’s important to limit TeltoCharge to prevent breaking Circuit Breaker.

{| class="wikitable"
|+ Example settings
|-
! Setting !! Value !! Explanation
|-
| Power selector switch || Must be selected according to the installation details || Link to QUG
|-
| Connectivity || Connect TeltoCharge to your local Wifi || Link to QUG
|-
| 3 phase charging || ON || Link to QUG
|-
| Phase priority || Select phase from which you would to charge when operating on single phase mode || Link to QUG
|-
|}
=2.Installation with the smart meter using DLB =
Installation type, when TeltoCharge is connected with the Smart meter (list to supported smart meters) .
TeltoCharge have the ability to communicate with dedicated smart energy meter and regarding to its readings, adjust used electrical power. Such functionality allows to protection house electrical grid from overload in peak hours and optimize energy usage to meet user habits. A smart energy meter should always be installed in source electrical cabinet as showed below.
{| class="wikitable"
|+ Caption text
|-
! Setting !! Header text !! Header text
|-
| Power selector switch || Must be selected according to the installation details.
You also could limit the maximum output to the CAR
| Example
|-
| Connectivity || Connect TeltoCharge to your local Wifi || Example
|-
| Location is ventilated || Change to yes, if installation is outside || Example
|-
| 3 phase charging || ON || Example
|-
| Phase priority || Select phase from which you would to charge when operating on single phase mode || Example
|-
| Dynamic Load Balancing || Select what you would be using:

* Modbus RTU METER/Inverter

* CT clamps

Enable Dynamic Load Balancing
| Example
|-
| Max grid Load || Select the value of the main house inlet || Example
|-
| Solar Charging || If Solar panels are installed, this function should be turned on || Example
|-
| Search for device || TeltoCharge will try to establish communication with the Modbus RTU device || Example
|-
| Other Funtionalities || Here you could read more about all other functionalities || Example
|}