Solar integration EVC2 - Revision history

KarolisS: KarolisS moved page Solar integrationEVC2 to Solar integration EVC2 without leaving a redirect: Misspelled title

2025-08-05T09:48:23Z

KarolisS moved page Solar integrationEVC2 to Solar integration EVC2 without leaving a redirect: Misspelled title

← Older revision		Revision as of 12:48, 5 August 2025
(No difference)

KarolisS at 13:04, 4 August 2025

2025-08-04T13:04:35Z

← Older revision		Revision as of 16:04, 4 August 2025
Line 55:		Line 55:
	:[[File:EVC2 eco 1 phase v2.png\|800x800px]]		:[[File:EVC2 eco 1 phase v2.png\|800x800px]]
	*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.		*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
	:~~Example~~:
	:[[File:~~ECO+ example~~.png\|~~frameless~~\|900x900px~~\|none~~]]		:'''3 phase charging examples:'''
			:[[File:EVC2 ecoplus 3 phase v2.png\|900x900px]]

			:'''Single phase charging examples:'''
			:[[File:EVC2 ecoplus 1 phase v2.png\|900x900px]]

	== Additional information ==		== Additional information ==
	There is additional information that is important to know when using solar integration, specifically regarding timers that dictate the start and stop of the charging process.		There is additional information that is important to know when using solar integration, specifically regarding timers that dictate the start and stop of the charging process.

KarolisS at 11:33, 24 July 2025

2025-07-24T11:33:09Z

← Older revision		Revision as of 14:33, 24 July 2025
Line 36:		Line 36:

	== Charging mode explanation ==		== Charging mode explanation ==
	This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check [[~~IN APP DIAGNOSTICS~~\|this app guide]]. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>		This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check [[In app diagnostics\|this app guide]]. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>

	*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum of '''6A''' is required to charge the EV. If there is less surplus energy available than 6A, the charger will remain in "On hold" mode.		*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum of '''6A''' is required to charge the EV. If there is less surplus energy available than 6A, the charger will remain in "On hold" mode.

KarolisS at 11:31, 24 July 2025

2025-07-24T11:31:16Z

← Older revision		Revision as of 14:31, 24 July 2025
Line 36:		Line 36:

	== Charging mode explanation ==		== Charging mode explanation ==
	This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check this app guide. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>		This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check [[IN APP DIAGNOSTICS\|this app guide]]. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>

	*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum of '''6A''' is required to charge the EV. If there is less surplus energy available than 6A, the charger will remain in "On hold" mode.		*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum of '''6A''' is required to charge the EV. If there is less surplus energy available than 6A, the charger will remain in "On hold" mode.

KarolisS at 11:39, 23 July 2025

2025-07-23T11:39:14Z

← Older revision		Revision as of 14:39, 23 July 2025
Line 38:		Line 38:
	This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check this app guide. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>		This section demonstrates the charger's behavior in various configurations and its response to fluctuations in available solar power. In these examples we'll be using 3 phases as input for the charger. For detailed information on diagnosing the power draw on each phase, please check this app guide. The TeltoCharge EV charger offers three solar charging modes, each providing unique benefits for different situations:<br>

	*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum required ~~value is 6 Amps~~. If there is less surplus energy available than ~~6 A~~, the charger will remain in "On hold" mode.		*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum of '''6A''' is required to charge the EV. If there is less surplus energy available than 6A, the charger will remain in "On hold" mode.
	:'''3 phase charging examples:'''		:'''3 phase charging examples:'''
	:[[File:EVC2 solar only 3 phase v2.png\|900x900px]]		:[[File:EVC2 solar only 3 phase v2.png\|900x900px]]
Line 44:		Line 44:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:[[File:EVC2 solar only 1 phase v2.png\|900x900px]]		:[[File:EVC2 solar only 1 phase v2.png\|900x900px]]
	*'''ECO charging profile''' - In this mode, charging begins by ~~blending~~ available solar power with energy from the grid. ~~A smart~~ meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of power ~~available to be~~ used from the grid. A minimum of '''6A''' is required to charge the EV.		*'''ECO charging profile''' - In this mode, charging begins by combining available solar power with energy from the grid. Smart meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of available power used from the grid. A minimum of '''6A''' is required to charge the EV.

	:The user sets ECO minimum value, which is the minimum charging current the solar power will be used for. The system prioritizes using all available solar power to meet this target, supplementing it with grid power only as needed. However, if no solar power is being generated, the charger will still use the grid to charge the vehicle, provided enough power is available.		:The user sets ECO minimum value, which is the minimum charging current the solar power will be used for. The system prioritizes using all available solar power to meet this target, supplementing it with grid power only as needed. However, if no solar power is being generated, the charger will still use the grid to charge the vehicle, provided enough power is available.

KarolisS at 09:39, 23 July 2025

2025-07-23T09:39:59Z

← Older revision		Revision as of 12:39, 23 July 2025
Line 44:		Line 44:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:[[File:EVC2 solar only 1 phase v2.png\|900x900px]]		:[[File:EVC2 solar only 1 phase v2.png\|900x900px]]
	*'''ECO charging profile''' - In this mode, charging begins by blending available solar power with energy from the grid. A smart meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of power available to be used from the grid.		*'''ECO charging profile''' - In this mode, charging begins by blending available solar power with energy from the grid. A smart meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of power available to be used from the grid. A minimum of '''6A''' is required to charge the EV.

	:The user sets ECO minimum value, which is the minimum charging current the solar power will be used for. The system prioritizes using all available solar power to meet this target, supplementing it with grid power only as needed. However, if no solar power is being generated, the charger will still use the grid to charge the vehicle, provided enough power is available.		:The user sets ECO minimum value, which is the minimum charging current the solar power will be used for. The system prioritizes using all available solar power to meet this target, supplementing it with grid power only as needed. However, if no solar power is being generated, the charger will still use the grid to charge the vehicle, provided enough power is available.
Line 53:		Line 53:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:		:
	:[[File:EVC2 eco 1 phase v2.png\|~~900x900px~~]]		:[[File:EVC2 eco 1 phase v2.png\|800x800px]]
	*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.		*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
	:Example:		:Example:

KarolisS at 09:36, 23 July 2025

2025-07-23T09:36:01Z

← Older revision		Revision as of 12:36, 23 July 2025
Line 53:		Line 53:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:		:
	[[File:EVC2 eco 1 phase v2.png\|900x900px]]		:[[File:EVC2 eco 1 phase v2.png\|900x900px]]
	*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.		*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
	:Example:		:Example:

KarolisS at 09:35, 23 July 2025

2025-07-23T09:35:13Z

← Older revision		Revision as of 12:35, 23 July 2025
Line 53:		Line 53:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:		:
			[[File:EVC2 eco 1 phase v2.png\|900x900px]]
	*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.		*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
	:Example:		:Example:

KarolisS at 09:28, 23 July 2025

2025-07-23T09:28:16Z

← Older revision		Revision as of 12:28, 23 July 2025
Line 40:		Line 40:
	*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum required value is 6 Amps. If there is less surplus energy available than 6 A, the charger will remain in "On hold" mode.		*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum required value is 6 Amps. If there is less surplus energy available than 6 A, the charger will remain in "On hold" mode.
	:'''3 phase charging examples:'''		:'''3 phase charging examples:'''
	:[[File:EVC2 solar only 3 phase.png\|900x900px]]		:[[File:EVC2 solar only 3 phase v2.png\|900x900px]]
	:		:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:[[File:EVC2 solar only 1 phase.png\|900x900px]]		:[[File:EVC2 solar only 1 phase v2.png\|900x900px]]

	*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
	~~:Example:<br>~~
	~~:[[File:ECO+ example.png\|frameless\|900x900px\|none]]~~


	*'''ECO charging profile''' - In this mode, charging begins by blending available solar power with energy from the grid. A smart meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of power available to be used from the grid.		*'''ECO charging profile''' - In this mode, charging begins by blending available solar power with energy from the grid. A smart meter is required to measure the power available on each phase. In the following examples, the '''"from grid"''' value indicates the amount of power available to be used from the grid.

Line 55:		Line 49:

	:'''3 phase charging examples:'''		:'''3 phase charging examples:'''
	:[[File:EVC2 eco 3 phase.png\|900x900px]]		:[[File:EVC2 eco 3 phase v2.png\|900x900px]]
	:		:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:[[File:~~EVC2 eco 1 phase~~.png\|~~800x800px~~]]		:
			*'''ECO+ charging profile''' - In this profile, the charging process is initiated using a combination of solar energy and grid energy. The user sets the ECO+ surplus minimum value, which determines the minimum surplus energy required to start the charging process. If the set value is less than 6A, the difference in current will be supplemented with grid power.
			:Example:
			:[[File:ECO+ example.png\|frameless\|900x900px\|none]]
	== Additional information ==		== Additional information ==
	There is additional information that is important to know when using solar integration, specifically regarding timers that dictate the start and stop of the charging process.		There is additional information that is important to know when using solar integration, specifically regarding timers that dictate the start and stop of the charging process.

KarolisS at 13:26, 22 July 2025

2025-07-22T13:26:19Z

← Older revision		Revision as of 16:26, 22 July 2025
Line 40:		Line 40:
	*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum required value is 6 Amps. If there is less surplus energy available than 6 A, the charger will remain in "On hold" mode.		*'''Solar only charging profile''' - In this profile, the charging process is initiated solely using green energy. The minimum required value is 6 Amps. If there is less surplus energy available than 6 A, the charger will remain in "On hold" mode.
	:'''3 phase charging examples:'''		:'''3 phase charging examples:'''
	:[[File:EVC2 solar only 3 phase.png]]		:[[File:EVC2 solar only 3 phase.png\|900x900px]]
	:		:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
Line 58:		Line 58:
	:		:
	:'''Single phase charging examples:'''		:'''Single phase charging examples:'''
	:[[File:EVC2 eco 1 phase.png\|~~900x900px~~]]		:[[File:EVC2 eco 1 phase.png\|800x800px]]

	== Additional information ==		== Additional information ==