Potential free contact - Revision history

KarolisS at 10:50, 15 July 2025

2025-07-15T10:50:44Z

← Older revision		Revision as of 13:50, 15 July 2025
Line 1:		Line 1:
	==Potential free contact==		==Potential-free contact==

			[[File:Potential free contact location.png\|\|none]]

	This terminal is found on the interface board. It enables the following features, which are configurable in the app:		This terminal is found on the interface board. It enables the following features, which are configurable in the app:

	~~[[File:Potential free contact location.png\|\|none]]~~

	=== Option 1: Emergency stop ===		=== Option 1: Emergency stop ===
Line 46:		Line 46:
	By default this setting must be set to allow charging when circuit is open (Option 2).		By default this setting must be set to allow charging when circuit is open (Option 2).

	Potential free contact can work with or without DLM/SOLAR/OCPP integration.		Potential-free contact can work with or without DLM/SOLAR/OCPP integration.

	If charging was blocked by potential free contact and later unblocked, charger will apply randomized delay before starting charging (if it's enabled)		If charging was blocked by potential-free contact and later unblocked, charger will apply randomized delay before starting charging (if it's enabled)

	If charging was blocked by either '''Option 1 or Option 2''' and later unblocked, or its charging power was reduced by '''Option 3''' but was allowed to return to normal rate - charger will start charging from lowest possible power and later ramp up gradually (at a rate of 10% of the rated power per minute).		If charging was blocked by either '''Option 1 or Option 2''' and later unblocked, or its charging power was reduced by '''Option 3''' but was allowed to return to normal rate - charger will start charging from lowest possible power and later ramp up gradually (at a rate of 10% of the rated power per minute).
Line 54:		Line 54:
	Charger is able to send information to OCPP server informing it why charging is not allowed or why power is decreased.		Charger is able to send information to OCPP server informing it why charging is not allowed or why power is decreased.

	===Potential free contact examples===		===Potential-free contact examples===
	[[File:Potential free contact support.png]]		[[File:Potential free contact support.png]]

KarolisS at 10:49, 15 July 2025

2025-07-15T10:49:09Z

← Older revision		Revision as of 13:49, 15 July 2025
Line 53:		Line 53:

	Charger is able to send information to OCPP server informing it why charging is not allowed or why power is decreased.		Charger is able to send information to OCPP server informing it why charging is not allowed or why power is decreased.

			===Potential free contact examples===
			[[File:Potential free contact support.png]]

KarolisS at 09:47, 15 July 2025

2025-07-15T09:47:08Z

← Older revision		Revision as of 12:47, 15 July 2025
Line 3:		Line 3:
	This terminal is found on the interface board. It enables the following features, which are configurable in the app:		This terminal is found on the interface board. It enables the following features, which are configurable in the app:

	[[File:Potential free contact location.png\|~~frameless~~\|none]]		[[File:Potential free contact location.png\|\|none]]

	=== Option 1: Emergency stop ===		=== Option 1: Emergency stop ===

KarolisS: Protected "Potential free contact" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2025-07-15T09:33:23Z

Protected "Potential free contact" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 12:33, 15 July 2025
(No difference)

KarolisS at 09:32, 15 July 2025

2025-07-15T09:32:49Z

@@ Line 1: / Line 1: @@
-    This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.
+==Potential free contact==
-    If rotary switch is set to invalid, reserved value it will not charge and indicate that the following ways:
+This terminal is found on the interface board. It enables the following features, which are configurable in the app:
-    Yellow LED’s (on EVC1XX we used this LED sequence to indicate, that default settings are used. On EVC2XX we removed this LED sequence dependency on changing installer settings and only made it indicate invalid rotary switch position).
+[[File:Potential free contact location.png|frameless|none]]
-    Error in APP (Incorrect power rotary switch position).
+=== Option 1: Emergency stop ===
-    When power rotary switch position is adjusted or left in default position, static load balancing value adjusts automatically to configured max power. But later it must be possible to adjust it via APP.
+* If charging is in progress and the input state changes to trigger an emergency stop, the session is put ON HOLD.

DonatasL at 09:15, 12 June 2025

2025-06-12T09:15:25Z

← Older revision		Revision as of 12:15, 12 June 2025
Line 1:		Line 1:
	This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.		This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.
	By changing the rotary switch position it is possible to limit charger’s max output to the car.		By changing the rotary switch position it is possible to limit charger’s max output to the car.
	[[File:Rotary.png\|~~thumb~~\|none]]		[[File:Rotary.png\|frameless\|none]]
	By default (position 0) charger sets max possible output power.Possible values differ between different modification devices.		By default (position 0) charger sets max possible output power.Possible values differ between different modification devices.

DonatasL at 09:13, 12 June 2025

2025-06-12T09:13:21Z

← Older revision		Revision as of 12:13, 12 June 2025
Line 1:		Line 1:
	This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.		This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.
	By changing the rotary switch position it is possible to limit charger’s max output to the car.		By changing the rotary switch position it is possible to limit charger’s max output to the car.
	[[File:Rotary.png\|thumb]]		[[File:Rotary.png\|thumb\|none]]
	By default (position 0) charger sets max possible output power.Possible values differ between different modification devices.		By default (position 0) charger sets max possible output power.Possible values differ between different modification devices.

DonatasL: Created page with " This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''. By changing the rotary switch position it is possible to limit charger’s max output to the car. thumb By default (position 0) charger sets max possible output power.Possible values differ between different modification devices. If rotary switch is set to invalid, reserved value it will not charge and indicate that the follo..."

2025-06-12T09:12:52Z

Created page with " This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''. By changing the rotary switch position it is possible to limit charger’s max output to the car. thumb By default (position 0) charger sets max possible output power.Possible values differ between different modification devices. If rotary switch is set to invalid, reserved value it will not charge and indicate that the follo..."

New page

This switch could be found on the interface board. It could turned to to limit '''Maximum device output'''.
By changing the rotary switch position it is possible to limit charger’s max output to the car.
[[File:Rotary.png|thumb]]
By default (position 0) charger sets max possible output power.Possible values differ between different modification devices.

If rotary switch is set to invalid, reserved value it will not charge and indicate that the following ways:

Yellow LED’s (on EVC1XX we used this LED sequence to indicate, that default settings are used. On EVC2XX we removed this LED sequence dependency on changing installer settings and only made it indicate invalid rotary switch position).

Error in APP (Incorrect power rotary switch position).

When power rotary switch position is adjusted or left in default position, static load balancing value adjusts automatically to configured max power. But later it must be possible to adjust it via APP.