Eastron settings - Revision history

FiodorF at 11:56, 28 October 2026

2026-10-28T11:56:58Z

← Older revision		Revision as of 13:56, 28 October 2026
Line 1:		Line 1:
	~~← [[Smart energy meters]]~~		<div style="font-family:'Inter','Helvetica Neue',Arial,sans-serif; line-height:1.6;">
	~~===~~= ~~RS485 parameters for energy meters Eastron SMD54-M ; SMD72D~~-~~M V2 ====~~
	~~''Note 1~~: ~~Energy meter parameters should match EVSE default parameters.~~'' ~~<br>~~
	''~~Note 2~~: ~~Eastron energy meters booting time is longer than others~~.''

	{\| class="wikitable" style="text-align: center; border: ~~1px solid~~ #~~0054A6~~; font-family: ~~arial~~, sans-serif; ~~width~~: ~~60%~~;"		== <span style="font-family:'Oswald','Arial Narrow',sans-serif; text-transform:uppercase; letter-spacing:0.02em;">RS-485 parameters for Eastron SDM meters</span> ==

			''Note 1: The energy meter's parameters must match the EVSE (charger) parameters. The default values are listed below.''

			''Note 2: Eastron energy meters take longer to boot than other meters.''

			{\| class="wikitable" style="text-align:center; width:80%;"
			! style="background:#001A77; color:#FFFFFF; border-color:#001A77; font-family:'Oswald','Arial Narrow',sans-serif; text-transform:uppercase; letter-spacing:0.03em; font-weight:500; padding:8px;" \| RS-485 parameter
			! style="background:#001A77; color:#FFFFFF; border-color:#001A77; font-family:'Oswald','Arial Narrow',sans-serif; text-transform:uppercase; letter-spacing:0.03em; font-weight:500; padding:8px;" \| EVSE (charger) default value (configurable in the app)
	\|-		\|-
	~~! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;"~~ \| ~~RS485 parameter~~		\| Modbus address \|\| 1
	~~! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;"~~ \| ~~EVSE default parameter value (configurable in mobile app)~~
	\|-		\|-
	\| ~~style="padding: 8px;"~~ \| ~~Modbus adress~~		\| Baud rate \|\| 9600
	\| ~~style="padding: 8px;" \| 1~~
	\|-		\|-
	\| ~~style="padding: 8px;"~~ \| ~~Baud rate~~		\| Parity \|\| None
	\| ~~style="padding: 8px;" \| 9600~~
	\|-		\|-
	~~\| style="padding: 8px;" \| Parity~~		\| Stop bits \|\| 1
	~~\| style="padding: 8px;" \| None~~

	\|-
	~~\| style="padding: 8px;"~~ \| Stop bits
	\| ~~style="padding: 8px;"~~ \| 1

	\|}		\|}

	==== Configuring the meter in the mobile application ====		== <span style="font-family:'Oswald','Arial Narrow',sans-serif; text-transform:uppercase; letter-spacing:0.02em;">Configuring the meter in the mobile application</span> ==

	''Note: ~~Users~~ can use two meters with different addresses. ~~Additionally, there will be~~ settings ~~for these energy meters~~ in the installer menu ~~(these settings are the same for both energy meters)~~.''		''Note: You can use two meters with different addresses. Both meters share the same settings in the installer menu.''

			# Make sure your charger firmware and application are updated to the latest version (see [[Release notes: Firmware]] and the app for [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).
			# Enter the Installer menu, select Load Balancing, then Modbus RTU.<br>[[File:Settings-to-rtu.png\|frameless\|alt=Path to Modbus RTU settings\|576x576px]]
			# If the charger does not recognise the meter, go to Manual Setup and choose your meter model from the presets, or enter the values from the RS-485 parameters table manually.<br>[[File:Mod-to-manual.png\|frameless\|alt=Manual setup screen\|576x576px]]

	1. Make sure your charger firmware and application are updated to the latest version. (←[[Release notes: Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).		Once the meter is successfully configured, press Connect. You will receive a confirmation screen and the status will change. Possible statuses:
			* '''Connected''' – the meter is configured correctly.
	~~2. Enter the Installer menu, select Load Balancing, then Modbus RTU.~~		* '''Disconnected''' – a wrong parameter value is set on the charger, or the meter is not wired correctly.
			* '''Wrong type''' – the meter configuration does not match the connected meter.
	~~[[File:Settings-to-rtu.png\|frameless\|576x576px]]~~		* '''Not supported''' – the connected meter is not compatible with the installation.

	~~3. If the charger does not recognize the meter, go to Manual Setup to use a device preset (choose the model of ''your meter'') or enter the settings from the RS485 parameters table manually.~~

	~~[[File:Mod-to-manual.png\|frameless\|576x576px]]~~

	Once the meter is successfully configured, press Connect. You will receive a confirmation screen and ~~its~~ status will change ~~to "~~'''Connected'''". ~~<br>If you get the status: <br>~~'''Disconnected''' - wrong ~~EVSE~~ parameter value is set or meter is not wired correctly. ~~<br>~~'''Wrong type''' - the meter configuration does not match ~~one that is currently~~ connected. ~~<br>~~'''Not supported''' - the connected meter is not compatible with the installation.


	For detailed settings, refer to the energy meter's official documentation.		For detailed settings, refer to the energy meter's official documentation.

			</div>

			[[Category:Smart energy meter mastersheet]]
	← [[Smart energy ~~meters~~]]

FiodorF at 12:02, 28 August 2026

2026-08-28T12:02:05Z

← Older revision		Revision as of 14:02, 28 August 2026
Line 24:		Line 24:
	\|}		\|}

	==== ~~How to configure Smart energy~~ meter in mobile application ====		==== Configuring the meter in the mobile application ====

	''Note: Users ~~could~~ use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''		''Note: Users can use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''


	1. Make sure ~~you have~~ updated ~~mobile application and firmware version of the charger~~ to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).		1. Make sure your charger firmware and application are updated to the latest version. (←[[Release notes: Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).

	2. ~~Go to installer~~ menu ~~in your application and set general parameters from table above:~~		2. Enter the Installer menu, select Load Balancing, then Modbus RTU.

	[[~~file~~:~~General_meter_settings~~.png~~\|alt=\|left~~\|frameless\|]]		[[File:Settings-to-rtu.png\|frameless\|576x576px]]

			3. If the charger does not recognize the meter, go to Manual Setup to use a device preset (choose the model of ''your meter'') or enter the settings from the RS485 parameters table manually.

			[[File:Mod-to-manual.png\|frameless\|576x576px]]

			Once the meter is successfully configured, press Connect. You will receive a confirmation screen and its status will change to "'''Connected'''". <br>If you get the status: <br>'''Disconnected''' - wrong EVSE parameter value is set or meter is not wired correctly. <br>'''Wrong type''' - the meter configuration does not match one that is currently connected. <br>'''Not supported''' - the connected meter is not compatible with the installation.


			For detailed settings, refer to the energy meter's official documentation.






	~~3. To get data form energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section:~~

	~~[[file:Dynamic_load_balancing.png\|alt=\|left\|frameless\|]]~~














	~~4. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it:~~

	~~[[file:Meter_for_power_consumption_calculation.png\|alt=\|left\|frameless\|]]~~










	~~To find out specific~~ settings, ~~you will need~~ to ~~read~~ the energy meter's documentation.



	← [[Smart energy meters]]		← [[Smart energy meters]]

PauliusKo at 08:33, 8 May 2023

2023-05-08T08:33:32Z

← Older revision		Revision as of 10:33, 8 May 2023
Line 1:		Line 1:
			← [[Smart energy meters]]
	==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ====		==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ====
	''Note 1: Energy meter parameters should match EVSE default parameters.'' <br>		''Note 1: Energy meter parameters should match EVSE default parameters.'' <br>

PauliusKo at 08:09, 13 March 2023

2023-03-13T08:09:23Z

← Older revision		Revision as of 10:09, 13 March 2023
Line 22:		Line 22:

	\|}		\|}

			==== How to configure Smart energy meter in mobile application ====

			''Note: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''


			1. Make sure you have updated mobile application and firmware version of the charger to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).

			2. Go to installer menu in your application and set general parameters from table above:

			[[file:General_meter_settings.png\|alt=\|left\|frameless\|]]












			3. To get data form energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section:

			[[file:Dynamic_load_balancing.png\|alt=\|left\|frameless\|]]














			4. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it:

			[[file:Meter_for_power_consumption_calculation.png\|alt=\|left\|frameless\|]]










			To find out specific settings, you will need to read the energy meter's documentation.



	← [[Smart energy meters]]		← [[Smart energy meters]]

PauliusKo at 07:17, 13 March 2023

2023-03-13T07:17:13Z

← Older revision		Revision as of 09:17, 13 March 2023
Line 22:		Line 22:

	\|}		\|}


			← [[Smart energy meters]]

PauliusKo: /* RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 */

2023-03-10T09:15:50Z

RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2

← Older revision		Revision as of 11:15, 10 March 2023
Line 1:		Line 1:
	==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ====		==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ====
	''Note: Energy meter parameters should match EVSE default parameters.''		''Note 1: Energy meter parameters should match EVSE default parameters.'' <br>
			''Note 2: Eastron energy meters booting time is longer than others.''

	{\| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"		{\| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"

PauliusKo: Protected "Eastron settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2023-03-10T08:20:01Z

Protected "Eastron settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 10:20, 10 March 2023
(No difference)

PauliusKo: Created page with "==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ==== ''Note: Energy meter parameters should match EVSE default parameters.'' {| class="wikitable" styl..."

2023-03-10T08:19:56Z

Created page with "==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ==== ''Note: Energy meter parameters should match EVSE default parameters.'' {| class="wikitable" styl..."

New page

==== RS485 parameters for energy meters Eastron SMD54-M ; SMD72D-M V2 ====
''Note: Energy meter parameters should match EVSE default parameters.''

{| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"
|-
! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" | RS485 parameter
! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" | EVSE default parameter value (configurable in mobile app)
|-
| style="padding: 8px;" | Modbus adress
| style="padding: 8px;" | 1
|-
| style="padding: 8px;" | Baud rate
| style="padding: 8px;" | 9600
|-
| style="padding: 8px;" | Parity
| style="padding: 8px;" | None

|-
| style="padding: 8px;" | Stop bits
| style="padding: 8px;" | 1

|}