Acrel settings - Revision history

FiodorF at 11:59, 28 August 2026

2026-08-28T11:59:45Z

← Older revision		Revision as of 14:59, 28 August 2026
Line 18:		Line 18:
	\| style="padding: 8px;" \|1		\| style="padding: 8px;" \|1
	\|}		\|}
	====~~How to configure Smart energy~~ meter in mobile application====		==== Configuring the meter in the mobile application ====
	====''Note: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''====
	1. Make sure you have updated mobile application and firmware version of the charger to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).

	2. ~~Go to~~ installer menu ~~in your application and set general parameters from table below~~.		''Note: Users can use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''

	~~3. To get data from energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section.~~

	4. ~~Also, you will need~~ to ~~set~~ the ~~kWh meter address in the “Meter for power consumption calculation” section if you want to use it~~.		1. Make sure your charger firmware and application are updated to the latest version. (←[[Release notes: Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).
	[[~~file~~:~~General_meter_settings~~.~~png\|alt~~=~~\|left\|frameless\|]~~]

	~~[[file:Dynamic_load_balancing~~.~~png\|alt=\|left\|frameless\|]]~~		2. Enter the Installer menu, select Load Balancing, then Modbus RTU.

	[[~~file~~:~~Meter_for_power_consumption_calculation~~.png\|~~alt=~~\|~~left~~\|frameless\|]] <br>		[[File:Settings-to-rtu.png\|frameless\|576x576px]]

			3. If the charger does not recognize the meter, go to Manual Setup to use a device preset (choose the model of ''your meter'') or enter the settings from the RS485 parameters table manually.

			[[File:Mod-to-manual.png\|frameless\|576x576px]]

			Once the meter is successfully configured, press Connect. You will receive a confirmation screen and its status will change to "'''Connected'''". <br>If you get the status: <br>'''Disconnected''' - wrong EVSE parameter value is set or meter is not wired correctly. <br>'''Wrong type''' - the meter configuration does not match one that is currently connected. <br>'''Not supported''' - the connected meter is not compatible with the installation.


			For detailed settings, refer to the energy meter's official documentation.



			← [[Smart energy meters]]

FurkaA at 11:46, 3 September 2024

2024-09-03T11:46:24Z

← Older revision		Revision as of 14:46, 3 September 2024
Line 1:		Line 1:
	~~← [[Smart energy meters]]~~
	~~====RS485 parameters for energy meter Acrel DTSD 1352====~~
	''Note: Energy meter parameters should match EVSE default parameters.''		''Note: Energy meter parameters should match EVSE default parameters.''
	{\| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"		{\| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"

FurkaA at 11:45, 3 September 2024

2024-09-03T11:45:51Z

← Older revision		Revision as of 14:45, 3 September 2024
Line 1:		Line 1:
	← [[Smart energy meters]]		← [[Smart energy meters]]
			====RS485 parameters for energy meter Acrel DTSD 1352====
			''Note: Energy meter parameters should match EVSE default parameters.''
			{\| class="wikitable" style="text-align: center; border: 1px solid #0054A6; font-family: arial, sans-serif; width: 60%;"
			\|-
			! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" \|RS485 parameter
			! style="background-color: #0054A6; color:#FFFFFF; padding: 8px;" \|EVSE default parameter value (configurable in mobile app)
			\|-
			\| style="padding: 8px;" \|Modbus adress
			\| style="padding: 8px;" \|1
			\|-
			\| style="padding: 8px;" \|Baud rate
			\| style="padding: 8px;" \|9600
			\|-
			\| style="padding: 8px;" \|Parity
			\| style="padding: 8px;" \|None
			\|-
			\| style="padding: 8px;" \|Stop bits
			\| style="padding: 8px;" \|1
			\|}
			====How to configure Smart energy meter in mobile application====
			====''Note: Users could use two meters with different addresses. Additionally, there will be settings for these energy meters in the installer menu (these settings are the same for both energy meters).''====
			1. Make sure you have updated mobile application and firmware version of the charger to the latest. (←[[Firmware]] and [https://apps.apple.com/lt/app/teltonika-energy/id1618750750 iOS] / [https://play.google.com/store/apps/details?id=com.teltonika.ems.ev&hl=en&gl=US Android]).

			2. Go to installer menu in your application and set general parameters from table below.

			3. To get data from energy meter, you will need to set the energy meter address in the “Dynamic load balancing” section.

			4. Also, you will need to set the kWh meter address in the “Meter for power consumption calculation” section if you want to use it.
			[[file:General_meter_settings.png\|alt=\|left\|frameless\|]]

			[[file:Dynamic_load_balancing.png\|alt=\|left\|frameless\|]]

			[[file:Meter_for_power_consumption_calculation.png\|alt=\|left\|frameless\|]] <br>

PauliusKo: Protected "Acrel settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

2023-10-23T13:16:47Z

Protected "Acrel settings" ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))

← Older revision		Revision as of 16:16, 23 October 2023
(No difference)

PauliusKo: Created page with "← Smart energy meters"

2023-10-23T13:16:42Z

Created page with "← Smart energy meters"

New page

← [[Smart energy meters]]